Nik Eftekhar Olivo

Prōtóplasto

An ultra-lightweight pavilion made almost entirely of plastic: three post-tensioned Hollow-Core 3D-printed columns carry radial space-frame roofs with 3D-printed joints, spanning 5.5 m at 3.8 kg/m².

Year
2023
Location
Halter AG, Switzerland
Institution
ETH Zürich: Digital Building Technologies, MAS ETH DFAB 2022/23 (T2)
Collaborators
Matthias Leschok, Marirena Kladeftira, Benjamin Dillenburger, MAS ETH DFAB 2022/23
Category
Large-Scale 3D Printing, Robotic Fabrication, Prototypes and Demonstrators, Computational Design
Role
Co-tutor of the MAS ETH DFAB studio and co-author of the Fabricate 2024 publication
Prōtóplasto in a dark underground space: three illuminated 3D-printed columns carrying white space-frame roofs.

Project

Prōtóplasto is an ultra-lightweight pavilion made almost entirely of plastic, developed in “One (Hu)man Roof”, the twelve-week studio of the second term (T2) of the MAS ETH in Architecture and Digital Fabrication 2022/23, led by Digital Building Technologies. It combines two processes, each used where it performs best: Hollow-Core 3D Printing (HC3DP) for the vertical elements, and a space frame with 3D-printed joints for the horizontal ones. The project was published at Fabricate 2024.

Structure

The pavilion aggregates three “mushroom” units. Each unit consists of a concrete pedestal cast in an HC3DP mould, a 2.2 m HC3DP column that is post-tensioned and lit from inside, and a radial roof truss of 3D-printed nylon nodes and glass-fibre tubes. The roof spans 5.5 m between columns and cantilevers 3 m, and the whole structure weighs 3.8 kg/m².

Fabrication

The columns were printed in PETG with a SAEKI Robotics pellet extruder on an ABB IRB 6700, with a 24 mm nozzle and a 19 mm layer height. Each column has a single outline and a hollow core that houses the post-tensioning cable and the light. A nozzle with an internal “X” brace stiffens the bead. A 2.2 m column printed in four to six hours and weighed 10 kg with a plain section and 18 to 20 kg with the braced one, about ten times faster and with four to five times less material than a comparable column in conventional extrusion.

The space-frame nodes were printed in PA12 by HP Multi Jet Fusion as hollow shells, in three joint types with self-guiding, interlocking connections. In total, 291 PA12 connections join 535 glass-fibre rods of 20 mm, which were cut to length in a human-robot setup. The roof was pre-assembled into modules on site, each weighing 3.7 kg on average, so the pavilion was assembled entirely by hand, without scaffolding. Augmented reality on HoloLens glasses, phones and tablets guided the assembly of the modules and columns.

Exhibition

The pavilion was exhibited in an underground industrial space at Halter AG, surrounded by suspended 2.2 m HC3DP chandeliers, with no light in the room other than the light inside the printed elements.

My contribution

Co-tutor of the MAS ETH DFAB studio together with Matthias Leschok and Marirena Kladeftira, and co-author of the Fabricate 2024 paper.

Credits

Teaching team: Matthias Leschok, Marirena Kladeftira, Nik Eftekhar Olivo, with Prof. Benjamin Dillenburger (Digital Building Technologies).

MAS ETH DFAB 2022/23 students: Eleni Alexi, Adam Anouar, Ana Ascic, Keng Chia Chang, Xue Chen, Po Yen Chen, Ahmed Elmeraghy, Caitlin Emily Gallagher, Yixiao Huang, Yi Hsiu Hung, Chenming Jiang, Lihin Karunadhipathi, Joseph Kenny, Man Ki Ian Law, Ramon Lopez Maldonado, Nijat Mahamaliyev, Abhipsa Pal, Carl Pantos Conquilla, Etienne Pavoncello, Huang Su, Lee Yo Cheng, Zhuo Zhang.

Technical support: Tobias Hartmann, Philippe Fleischmann, Heinz Richner, Jonathan Leu, Michael Lyrenmann (Robotic Fabrication Laboratory).

Exhibition: Yanis Hofstetter (event coordination). Video: Girts Apskalns.

Sponsors and partners: Halter AG, SAEKI Robotics AG, Castioni Kunststoffe. Supported by the NCCR Digital Fabrication, funded by the Swiss National Science Foundation.

Playing the video loads content from YouTube. Open on YouTube

Publications

  • Leschok, M., Kladeftira, M., Eftekhar Olivo, N., & Dillenburger, B. (2024). Prōtóplasto: A discrete roof-column system with hollow-core 3D printing and bespoke space frames. Fabricate 2024: Creating Resourceful Futures. UCL Press. doi:10.2307/jj.11374766

Links

← All projects